{"product_id":"oxva-xlim-unitech-3-0-replacement-pods","title":"OXVA Xlim UNITECH 3.0 Replacement Pods","description":"\u003ch1\u003eOXVA Xlim UNITECH 3.0 Replacement Pods\u003c\/h1\u003e\n\u003cp\u003eOXVA Xlim UNITECH 3.0 Replacement Pods come in packs of three, with a single resistance in each pack: 0.4Ω, 0.6Ω, 0.8Ω or 1.2Ω. Each is a 2ml top-fill pod with a built-in UNITECH 3.0 mesh coil, and they fit the Xlim kits listed below. These are the standard pods, not the ABT versions, and this page explains the difference.\u003c\/p\u003e\n\u003cp\u003eIf your pod has run its course, or you want a tighter or more open draw, this is where you choose the right one. Pick a resistance, check your kit against the compatibility table, and confirm the fit before you order. You can also browse the wider \u003ca href=\"https:\/\/www.vapourcore.com\/collections\/oxva\"\u003eOXVA range\u003c\/a\u003e of kits and pods.\u003c\/p\u003e\n\n\u003ch2\u003eWhat Are OXVA Xlim UNITECH 3.0 Pods?\u003c\/h2\u003e\n\u003cp\u003eUNITECH 3.0 is the name OXVA gives to the mesh coil built into these pods. The coil is part of the pod rather than a separate part, so when a pod reaches the end of its life you replace the whole pod. Each pod is filled from the top through a silicone port, so you can refill it without taking it out of the device.\u003c\/p\u003e\n\u003cp\u003eEach pod holds 2ml, the UK TPD limit for refillable pods. Some international listings quote a larger figure, but 2ml is the capacity of the pods sold here. The four resistances cover two vaping styles: the lower 0.4Ω and 0.6Ω pods suit a more open restricted direct-to-lung draw (RDL, sometimes written RDTL), while the higher 0.8Ω and 1.2Ω pods suit a tighter mouth-to-lung (MTL) draw.\u003c\/p\u003e\n\n\u003ch2\u003eStandard UNITECH 3.0 or ABT Pods: What Is the Difference?\u003c\/h2\u003e\n\u003cp\u003eOXVA sells two closely related pod lines, and they are easy to mix up. Both use a built-in UNITECH 3.0 mesh coil. The difference is anti-burn. OXVA describes its Anti-Burn Technology, or ABT, as based on e-liquid-level detection, and it needs a dedicated ABT pod in an ABT-enabled kit such as the \u003ca href=\"https:\/\/www.vapourcore.com\/products\/oxva-xlim-4-pro-vape-kit\"\u003eOXVA Xlim 4 Pro\u003c\/a\u003e, also written Xlim Pro 4. The pods on this page are the standard version, without the anti-burn function.\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth\u003eStandard UNITECH 3.0 pods (this page)\u003c\/th\u003e\n\u003cth\u003eABT UNITECH 3.0 pods\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoil\u003c\/th\u003e\n\u003ctd\u003eBuilt-in UNITECH 3.0 mesh\u003c\/td\u003e\n\u003ctd\u003eBuilt-in UNITECH 3.0 mesh\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAnti-burn function\u003c\/th\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eYes, based on e-liquid-level detection\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHow to spot them\u003c\/th\u003e\n\u003ctd\u003eStandard base contacts, no red ring\u003c\/td\u003e\n\u003ctd\u003eFour base contacts, ABT marking on the base, red mouthpiece ring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIn an ABT-enabled kit\u003c\/th\u003e\n\u003ctd\u003eWorks as a normal pod, without anti-burn\u003c\/td\u003e\n\u003ctd\u003eAnti-burn and refill alert are active\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eNot sure which pod you have? Check the base and the mouthpiece against the table above.\u003c\/p\u003e\n\n\u003ch2\u003eChoose Your Resistance\u003c\/h2\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eResistance\u003c\/th\u003e\n\u003cth\u003ePower range\u003c\/th\u003e\n\u003cth\u003eStyle\u003c\/th\u003e\n\u003cth\u003eBest for\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0.4Ω\u003c\/td\u003e\n\u003ctd\u003e26-30W\u003c\/td\u003e\n\u003ctd\u003eRDL\u003c\/td\u003e\n\u003ctd\u003eA looser, more open draw with warmer, fuller vapour. Typically handles higher-VG e-liquid better.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0.6Ω\u003c\/td\u003e\n\u003ctd\u003e20-25W\u003c\/td\u003e\n\u003ctd\u003eRDL\u003c\/td\u003e\n\u003ctd\u003eAn open draw with a little more restriction than 0.4Ω. Typically handles higher-VG e-liquid better.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0.8Ω\u003c\/td\u003e\n\u003ctd\u003e12-18W\u003c\/td\u003e\n\u003ctd\u003eMTL\u003c\/td\u003e\n\u003ctd\u003eA tighter, cigarette-style draw. Suits 50\/50 e-liquid or nic salts.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1.2Ω\u003c\/td\u003e\n\u003ctd\u003e10-12W\u003c\/td\u003e\n\u003ctd\u003eMTL\u003c\/td\u003e\n\u003ctd\u003eThe tightest draw of the four, at the lowest power. Suits nic salts.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eMouth-to-lung, or MTL, is a tighter draw taken into the mouth first and then inhaled. Restricted direct-to-lung, or RDL, is a looser draw with more airflow. Match the power range to the setting on your kit, and with a new pod start at the lower end of the range before moving up. If you are unsure, the 0.6Ω pod is a sensible place to start for an open draw, and the 0.8Ω pod for a tight one.\u003c\/p\u003e\n\n\u003ch2\u003eWhich Xlim Kits Do They Fit?\u003c\/h2\u003e\n\u003cp\u003eStandard UNITECH 3.0 pods fit the Xlim family. Check your kit in the table before you order, because a small number of OXVA devices use different cartridges.\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eCompatibility\u003c\/th\u003e\n\u003cth\u003eKits\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFits\u003c\/td\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/www.vapourcore.com\/products\/oxva-xlim-4-vape-kit\"\u003eXlim 4\u003c\/a\u003e, Xlim Pro 3, Xlim 3 Ultra, Xlim Pro 2, Xlim Pro 2 DNA, Xlim SQ Pro 2, Xlim Go 2, Xlim Go Lite, Xlim Classic, Xlim SE, Xlim SE 2, Xlim Pro and Xlim SQ Pro\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFits, without anti-burn\u003c\/td\u003e\n\u003ctd\u003eXlim 4 Pro (Xlim Pro 4): standard pods work as a normal pod, but ABT needs a dedicated ABT pod\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDoes not fit\u003c\/td\u003e\n\u003ctd\u003eXlim C and NeXLIM, which need their own cartridges\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eIf you use a third-party device, check its manufacturer's pod compatibility before ordering.\u003c\/p\u003e\n\n\u003ch2\u003eHow to Fill and Prime Your Pod\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eFill.\u003c\/strong\u003e Open the silicone port on top of the pod and fill with e-liquid up to the line. You can do this with the pod still in your kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClose.\u003c\/strong\u003e Press the silicone port fully shut to seal the pod.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrime.\u003c\/strong\u003e Wait around 30 seconds for the mesh coil to absorb the e-liquid before your first draw.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStart low.\u003c\/strong\u003e Begin at the lower end of the power range for your resistance, then raise it if you want a warmer draw.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDraw gently.\u003c\/strong\u003e Take a few gentle puffs first rather than a long, hard pull.\u003c\/li\u003e\n\u003c\/ol\u003e\n\n\u003ch2\u003eLeak Protection and Coil Life\u003c\/h2\u003e\n\u003cp\u003eThe coil is built in and cannot be replaced on its own, so the life of the pod is the life of the coil. No pod is completely leak-proof, but most leaks come down to filling. Do not fill past the line, press the silicone port fully shut after every refill, and keep the device upright where you can.\u003c\/p\u003e\n\u003cp\u003ePod life depends on resistance, power and what you vape. Sweeter, thicker e-liquids and higher power tend to wear a coil faster. The signs it is time for a fresh pod are fading flavour, thinner vapour, or a burnt taste that does not clear after a refill and a short wait. There is no fixed figure, so replace the pod when performance drops rather than by the calendar.\u003c\/p\u003e\n\n\u003ch2\u003eWhich E-Liquid to Use\u003c\/h2\u003e\n\u003cp\u003eStandard UNITECH 3.0 pods work with 50\/50 e-liquid and nic salts. The tighter 0.8Ω and 1.2Ω pods suit those best, and nic salts are the usual choice for higher strengths in a tight draw because they feel smoother. The more open 0.4Ω and 0.6Ω pods typically handle higher-VG e-liquid better, though this depends on the liquid and your device, and lower nicotine strengths are generally more comfortable there because you draw in more vapour per puff. Browse our \u003ca href=\"https:\/\/www.vapourcore.com\/collections\/nic-salt-e-liquid\"\u003enic salt e-liquid\u003c\/a\u003e range to match your pod.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eProduct\u003c\/th\u003e\n\u003ctd\u003eOXVA Xlim UNITECH 3.0 Replacement Pods (standard, non-ABT)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePack\u003c\/th\u003e\n\u003ctd\u003e3 pods per pack, one resistance per pack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eResistances\u003c\/th\u003e\n\u003ctd\u003e0.4Ω, 0.6Ω, 0.8Ω, 1.2Ω\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower range\u003c\/th\u003e\n\u003ctd\u003e0.4Ω 26-30W, 0.6Ω 20-25W, 0.8Ω 12-18W, 1.2Ω 10-12W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVaping style\u003c\/th\u003e\n\u003ctd\u003e0.4Ω and 0.6Ω RDL, 0.8Ω and 1.2Ω MTL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCapacity\u003c\/th\u003e\n\u003ctd\u003e2ml per pod (UK TPD)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoil\u003c\/th\u003e\n\u003ctd\u003eBuilt-in UNITECH 3.0 mesh, not user-replaceable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFilling\u003c\/th\u003e\n\u003ctd\u003eTop-fill via silicone port, without removing the pod\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePriming\u003c\/th\u003e\n\u003ctd\u003eAround 30 seconds\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eE-liquid\u003c\/th\u003e\n\u003ctd\u003e50\/50 or nic salts, higher-VG typically suits 0.4Ω and 0.6Ω\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003eApproximately 24.1 x 13.8 x 34.1mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCompatibility\u003c\/th\u003e\n\u003ctd\u003eXlim family, see the compatibility table above\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eNot compatible\u003c\/th\u003e\n\u003ctd\u003eXlim C and NeXLIM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIn the box\u003c\/th\u003e\n\u003ctd\u003e3 x UNITECH 3.0 replacement pods\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eDelivery and Returns\u003c\/h2\u003e\n\u003cp\u003eAdd as many packs as you need to the same order as your e-liquid, remembering that each pack is a single resistance. Pods are a regular replacement, so many people add a spare pack to the same order and keep a fresh pod to hand. Options and timescales are on our \u003ca href=\"https:\/\/www.vapourcore.com\/pages\/delivery-and-shipping\"\u003edelivery and shipping\u003c\/a\u003e page, and if anything needs to come back, our \u003ca href=\"https:\/\/www.vapourcore.com\/pages\/returns\"\u003ereturns\u003c\/a\u003e page explains how. Every order is age-verified at checkout.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\n\u003ch3\u003eWhat is the difference between standard UNITECH 3.0 pods and ABT pods?\u003c\/h3\u003e\n\u003cp\u003eBoth use a built-in UNITECH 3.0 mesh coil. The difference is anti-burn: OXVA's ABT pods work with e-liquid-level detection in an ABT-enabled kit, while standard pods do not have that function. Standard pods have the usual base contacts and no red mouthpiece ring, whereas ABT pods have four base contacts, an ABT base marking and a red ring.\u003c\/p\u003e\n\n\u003ch3\u003eWhich Xlim kits do these pods fit?\u003c\/h3\u003e\n\u003cp\u003eStandard UNITECH 3.0 pods fit the Xlim family: Xlim 4, Xlim Pro 3, Xlim 3 Ultra, Xlim Pro 2, Pro 2 DNA, SQ Pro 2, Go 2, Go Lite, Classic, SE, SE 2, Pro and SQ Pro. They also work as a normal pod in the Xlim 4 Pro, without anti-burn. Check your kit's name against the compatibility table before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eDo they fit the Xlim C or NeXLIM?\u003c\/h3\u003e\n\u003cp\u003eNo. The Xlim C and NeXLIM use their own cartridges, so UNITECH 3.0 pods are not interchangeable with them. If you are not sure which Xlim you own, check the name on the device or its packaging, then match it against the compatibility table on this page before you order.\u003c\/p\u003e\n\n\u003ch3\u003eWhich resistance should I choose?\u003c\/h3\u003e\n\u003cp\u003eChoose by draw style. The 0.8Ω pod (12-18W) and 1.2Ω pod (10-12W) give a tighter mouth-to-lung draw, the usual match for nic salts. The 0.6Ω pod (20-25W) and 0.4Ω pod (26-30W) give a looser restricted direct-to-lung draw with warmer vapour. If you prefer a tight, cigarette-style draw, start with 0.8Ω or 1.2Ω.\u003c\/p\u003e\n\n\u003ch3\u003eHow many pods are in a pack and how much does each hold?\u003c\/h3\u003e\n\u003cp\u003eEach pack contains three UNITECH 3.0 replacement pods, all in the same resistance, so choose the resistance before you add to basket. Each pod holds 2ml of e-liquid, the UK TPD capacity. You may see a larger figure quoted on international listings, but 2ml is the capacity of the pods sold here.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I fill and prime the pod?\u003c\/h3\u003e\n\u003cp\u003eOpen the silicone port on top of the pod, fill with e-liquid up to the line and press the port fully shut. You can do this without removing the pod from the kit. Then wait around 30 seconds for the mesh coil to absorb the liquid before your first draw, and start at the lower end of the power range.\u003c\/p\u003e\n\n\u003ch3\u003eHow long does a UNITECH 3.0 pod last?\u003c\/h3\u003e\n\u003cp\u003eThere is no fixed figure, because pod life depends on resistance, power, e-liquid and how often you vape. Sweeter, thicker liquids and higher power tend to wear a coil faster. Replace the pod when the flavour fades, vapour thins or you notice a burnt taste that does not clear after a refill and a short wait.\u003c\/p\u003e\n\n\u003ch3\u003eWhat e-liquid works best in UNITECH 3.0 pods?\u003c\/h3\u003e\n\u003cp\u003eStandard UNITECH 3.0 pods work with 50\/50 e-liquid and nic salts. The tighter 0.8Ω and 1.2Ω pods suit those best, with nic salts the usual pick for higher strengths. The more open 0.4Ω and 0.6Ω pods typically handle higher-VG e-liquid better, depending on the liquid, and lower nicotine strengths tend to be more comfortable because you draw in more vapour per puff.\u003c\/p\u003e\n\n\u003ch3\u003eCan I replace just the coil?\u003c\/h3\u003e\n\u003cp\u003eNo. The UNITECH 3.0 mesh coil is built into the pod and is not user-replaceable, so when the coil reaches the end of its life you replace the whole pod. The upside is simplicity: there is no separate coil to fit, so you simply swap in a fresh pod, fill it and let it prime.\u003c\/p\u003e\n\n\u003ch3\u003eDo UNITECH 3.0 pods leak, and how do I avoid it?\u003c\/h3\u003e\n\u003cp\u003eNo pod is completely leak-proof, but most leaks come down to filling. Do not fill past the line, press the silicone port fully shut after every refill, and keep the device upright where you can. If a pod keeps leaking despite this, it may have reached the end of its life, so replace it.\u003c\/p\u003e\n\n\u003ch2\u003eImportant Information\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eContains nicotine, which is a highly addictive substance, when filled with nicotine-containing e-liquid.\u003c\/li\u003e\n\u003cli\u003e18+ only. Not for non-smokers, non-nicotine users, pregnant or breastfeeding women.\u003c\/li\u003e\n\u003cli\u003eKeep out of reach of children and pets. Dispose of used pods responsibly.\u003c\/li\u003e\n\u003cli\u003eAge verification is required at checkout.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"OXVA","offers":[{"title":"0.4ohm","offer_id":58945604485503,"sku":"OXVAXlimUNITECH3.0ReplacementPods0.4ohm","price":7.45,"currency_code":"GBP","in_stock":true},{"title":"0.6ohm","offer_id":58945604518271,"sku":"OXVAXlimUNITECH3.0ReplacementPods0.6ohm","price":7.45,"currency_code":"GBP","in_stock":true},{"title":"0.8ohm","offer_id":58945604551039,"sku":"OXVAXlimUNITECH3.0ReplacementPods0.8ohm","price":7.45,"currency_code":"GBP","in_stock":true},{"title":"1.2ohm","offer_id":58945604583807,"sku":"OXVAXlimUNITECH3.0ReplacementPods1.2ohm","price":7.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0565\/3426\/9997\/files\/OXVA_Xlim_UNITECH_3.0_Replacement_Pods.webp?v=1794308945","url":"https:\/\/www.vapourcore.com\/products\/oxva-xlim-unitech-3-0-replacement-pods","provider":"Vapourcore®","version":"1.0","type":"link"}